Truyện Cười BlogTaPhiet KC

Chat Box


--------------:Search

Thứ Năm, 1 tháng 11, 2012

Windows Server 2003 Configure RRAS (Routing And Remote Access Service) Site To Site VPN


The following are the steps you would need to take if you want to configure a VPN on a Windows 2003 server where you only have a single network card (NIC) exposed to the Internet. What we will do here is configure a site-to-site VPN so that clients can connect securely while still allowing other types of web traffic such as HTTP (port 80) and/or RDP (port 3389) to connect. This method sets up a secure tunnel for clients while allowing other types of web-based services to still be open and exposed on the same network card.
Normally, when you set up a VPN, you should use a dedicated network card and a dedicated card for other traffic. In most cases, a site-to-site VPN would be the only service set up on a single network card and the firewall would be controlled by an external firewall in front of the server. But Microsoft does provide a way to configure Windows Server 2003 to allow VPN and other web services on the same card.


The way to do this is to have the VPN be the front facing network service exposed to the Internet. Then we configure Windows 2003 to run Network Address Translation (NAT) services to manage the traffic coming in from this card. The big problem is that you usually have to have a remote firewall configured in front of this server. But Microsoft provides a useful component in the NAT services called "Basic Firewall". This has a similar interface to Windows Firewall so it can be configured to allow / deny ports and services while the VPN is enabled. Here are the steps to configure Windows 2003:
In Administrative Tools, open the Routing and Remote Access dialog.
routing and remote access dialog
If you have the Windows Firewall running on your server, you will see a dialog that says that ICF must be disabled before continuing. If you see this dialog, you must disable your Windows Firewall before continuing. The next couple of steps show how to do this.
must disable ICS/Windows Firewall
In Administrative Tools, open the Services dialog and find the Windows Firewall/Internet Connection Sharing (ICS)entry. Click the "Stop the service" link to stop the service.
Services dialog
Double-click the service and set it's Startup type to "Disabled". This will make it so that the Windows Firewall does not run anymore and is completely disabled. Click OK.
Disable Windows Firewall
Right-click your server name in the Routing and Remote Access dialog (it should be the item with little server icon that has a red stop square on top of it) and select Configure and Enable Routing and Remote Access.
Click Next on the Routing and Remote Access Server Setup Wizard.
routing and remote access server setup wizard
Select Custom configuration and click Next.
custom configuration
In the Custom Configuration, select VPN access and NAT and basic firewall and click Next.
vpn access and nat and basic firewall
Click Finish to complete the setup.
complete routing and remote access setup
When you click Finish, a dialog will ask you if you want to start the server and being running the Routing and Remote Access. Choose Yes.
yes, start routing and remote access service
After you wait for just a second, the routing server comes online and you will see a tree of options open up underneath your server icon. Your server icon will also change from a red square to a green square to show you that it has been started successfully.
Right-click the NAT/Basic Firewall and choose New Interface from the context menu.
nat/basic firewall
We are going to configure the firewall settings for the connection that has the VPN running on it. Choose your network card by name from the list. In most cases, this will be Local Area Connection as this is the default name of the NIC that Windows assigns.
choose a nat card
in the Network Address Translation Properties dialog, select Basic firewall only.
basic firewall only
Click on the Services and Ports tab and click on IP Security (IKE).
ip security (ike)
Once you click on the IP Security (IKE) entry, a edit box will immediately come up. You need to set up where NAT should route this traffic when received in the firewall. Just set all traffic to route directly to the local server (since this is where all the services are running) by setting the IP to itself (127.0.0.1).
edit service
Do the same with IP Security (IKE NAT Traversal)VPN Gateway (L2TP/IPSec - running on this server), and VPN Gateway (PPTP). Each one will need to be set to 127.0.0.1 the same as the above dialog. NOTE: For any other ports you want to open, do the same process to expose them in the firewall. The IP Security and VPN Gateway are the only required to enable the VPN to actually show from the NAT service. Then click OK.
select ports to open
Right-click the server name (the one with the green icon) and select Properties.
properties
Click on the IP tab and select Static address pool. This will enable the Add button. Click the Add button to edit the range IP's. You need to set a static range of IP addresses that will be used on the internal network that the VPN creates.
ip range
Set a range for the IP addresses that will be assigned for the local network that the VPN creates. The Number of addresses will automatically be calculated for you. Click OK.
VERY IMPORTANT: Make sure you set a range for the IP addresses that is unique and not likely to be on another network or there will be conficts if the client connects from a network with the same subnet.
new address range
Click OK to close the properties dialog.
properties dialog
In Administrative Tools, open the Computer Management tool (unless you are running Active Directory on your server and then you would need to add the user from there). Tree open Local Users and Groups -> Users and right-click Users to select New User....
new user
Create the new user as you would normally. Click the Create button and then click Close to close the dialog.
new user dialog
Right-click the new user account you just created and select Properties.
user properties
We have to enable this account to allow VPN login to this server. On the user properties dialog, click on the Dial-intab. Then select Allow access. Click OK to apply the change.
user properties
Once the server is set up, you can configure a client to connect to the VPN. Here are the instructions to connect with Windows XP:
http://www.devtoolshed.com/content/connect-site-site-vpn-windows-xp

Hãy là người truy cập lịch sự !!!!
Hãy nhấn "like", "thank" hoặc "comment" bài viết nếu thấy hữu ích và cần thiết cho bạn !!!
Hãy truy cập và góp ý chia sẻ để Diễn đàn Blog TaPhiet_KC được phát triển hơn !!
mong đây sẽ là nơi cho các bạn vui chơi giải trí , học hỏi và chia sẻ kiến thức IT cho các bạn và cho mọi người đam mê công nghẹ và ứng dụng công nghệ !!!!!!!!

Chúc các bạn thành công !!!
Mọi chi tiết Xin liên hệ Ban quản trị Blog
Mọi sự trợ giúp trực tiếp xin liên hệ :
Email: taphietit@ymail.com
Yahoo: moitinhdaucuatoi_viet_hy@yahoo.com
Gmail: taphietit@gmail.com
                                                 Mobile: 0987530288  

Share/Save/Bookmark

Đăng nhận xét

More →
Chữ đậm Chữ nghiêng Chữ nghiêng 2 Chèn Link Chèn Link Mã hóa code Help ?Nhấn vào biểu tượng hoặc kiểu chữ hoặc chèn link sau đó nhấn nút Chọn rồi copy (Ctrl + C) để paste (Ctrl + V) vào khung viết bình luận. Mã hóa code nếu bạn muốn đưa code vào bình luận.

Chọn Xóa
Top